Appikon for BendSure: Conduit Bending

BendSure is a conduit-bending calculator for electricians: offsets, saddles, stub-ups…

Av Amanuel Getachew Shiferaw · Produktivitet
Debuts-poeng 82NyVær først med å vurdere

Hvorfor vi forventer det: Thorough, well-explained conduit bending calculator with clear value for electricians and a helpful bend-by-bend guide.

BendSure: Conduit Bending skjermbilde 1BendSure: Conduit Bending skjermbilde 2BendSure: Conduit Bending skjermbilde 3BendSure: Conduit Bending skjermbilde 4BendSure: Conduit Bending skjermbilde 5

Lignende Produktivitet-apper

Se de beste

Kort fortalt

BendSure: Conduit Bending is a productivity calculator for electricians that works out marks for offsets, saddles, stub-ups, 90s and rolling or parallel offsets. It gives each mark's position from the end of the conduit and the matching bender mark, with a step-by-step bend mode. It stands out for offering both the bender's table and exact trigonometry, with the difference shown when it is 1/16" or more.

Sammendrag fra Debuts, basert på oppføringen i App Store.

Flere Produktivitet-apper

Ukens beste nye Produktivitet-apper

Om appen

BendSure is a conduit-bending calculator for electricians: offsets, saddles, stub-ups, back-to-back 90s, rolling offsets and parallel offsets. Enter your measurements and get the marks to make on the conduit, measured from the end of the stick, plus the mark on your bender (arrow, star or rim notch) to line up with each one.

CALCULATORS • Offsets: bend toward the obstruction or from a first bend at X, at 10, 22.5, 30, 45 or 60 degrees (angles vary by calculator) • Rolling offsets • Parallel offsets with the marks for each conduit • 3-point saddles (45/22.5 and 60/30) • 4-point saddles • Stub-up 90s • Back-to-back 90s, long and short method

NUMBERED BENDS Marks are numbered from the end of the conduit, Mark 1 first. The sketch of the bend carries the same numbers, so you can see which bend each mark belongs to, and a diagram of the stick shows where each one goes.

BEND MODE Tap Start bending to work one bend per screen: the mark in big numbers, a tape strip that shows where it falls, the bender mark to line up, and a note when to rotate the conduit 180 degrees. Tap Bent. Next after each bend. The screen stays on while you work.

EXACT MATH OR YOUR BENDER'S TABLE Every result shows the math, the multiplier and shrink used, so you can check it against your own numbers. The default is your bender's table, the numbers printed in bender guides. Exact trigonometry is one tap away. When the two differ by 1/16" or more, the result shows both answers side by side ("Your bender's table gives ..." or "Exact gives ...") with one tap to switch.

SET UP FOR YOUR BENDER On first launch, set up your bender: Klein, IDEAL, Gardner Bender, Greenlee or your own take-up, plus conduit type (EMT, rigid or IMC) and trade size (1/2" to 1-1/4"). Take-up presets are built in where a published value exists; otherwise you enter the take-up printed on your bender head. Skip it and change it any time in Settings. The setup is shown at the top of every calculator, so you always know which size an answer was for.

READABLE MARKS Results are in fractions to 1/16", the way a tape reads. Prefer metric? Switch to centimeters in Settings. On an empty calculator, Try an example fills in a worked case; New job clears the inputs, with Undo.

FIVE LANGUAGES English, German, Spanish, French and Italian. BendSure follows your phone's language, or you pick one in Settings.

PRIVATE AND OFFLINE Works offline. Anonymous usage counts only; your measurements never leave the phone. No ads, no account, no subscription.

BendSure is a calculation aid. Check every mark before you bend, and follow your local code and your bender's instructions. Not affiliated with Klein Tools, IDEAL, Gardner Bender or Greenlee.

Spørsmål om BendSure: Conduit Bending

Hva er BendSure: Conduit Bending?
BendSure: Conduit Bending is a productivity calculator for electricians that works out marks for offsets, saddles, stub-ups, 90s and rolling or parallel offsets. It gives each mark's position from the end of the conduit and the matching bender mark, with a step-by-step bend mode. It stands out for offering both the bender's table and exact trigonometry, with the difference shown when it is 1/16" or more.
Er BendSure: Conduit Bending gratis?
Nei. BendSure: Conduit Bending er en betalt app.
Hvilke enheter fungerer BendSure: Conduit Bending på?
BendSure: Conduit Bending fungerer på iPhone.
Hvilke språk er BendSure: Conduit Bending tilgjengelig på?
BendSure: Conduit Bending er tilgjengelig på engelsk.
Hvem lager BendSure: Conduit Bending?
BendSure: Conduit Bending er laget av Amanuel Getachew Shiferaw. Aldersgrensen i App Store er 4+.
Hva er alternativer til BendSure: Conduit Bending?
Lignende apper på Debuts: ChickMark: Habit Tracker, Anvil, AirBuild.

Slik vurderer folk den

Logg inn for å vurdere denne appen. Det ærlige svaret teller.

Ingen vurderinger ennå. Har du prøvd den? Vær den første til å vurdere.

Oppdagelsessignaler

Hvordan AI og folk oppdager BendSure: Conduit Bending på Debuts
Klar for AIDelvis
78 % beskrevet for AI-matching
Kan oppdages nåLiveStrukturerte data på denne siden og Debuts API

Fortell oss hva du liker. Vi sender bare e-post når noe nytt passer, og utviklere legger ofte ved et tilbud til testere.

Hva slags apper
På min
Vis meg bare
Hvor ofte
Vi sender en lenke du må bekrefte. Du får ingenting før du har klikket på den.