App-ikon for BendSure: Conduit Bending

BendSure: Conduit Bending

Ikke gjort krav på

BendSure is a conduit-bending calculator for electricians: offsets, saddles, stub-ups…

Af Amanuel Getachew Shiferaw · Produktivitet
Debuts-score 82NyGiv den første bedømmelse

Derfor forventer vi det: Thorough, well-explained conduit bending calculator with clear value for electricians and a helpful bend-by-bend guide.

BendSure: Conduit Bending skærmbillede 1BendSure: Conduit Bending skærmbillede 2BendSure: Conduit Bending skærmbillede 3BendSure: Conduit Bending skærmbillede 4BendSure: Conduit Bending skærmbillede 5

Lignende Produktivitet-apps

Se de bedste

Kort fortalt

BendSure: Conduit Bending is a productivity calculator for electricians that works out marks for offsets, saddles, stub-ups, 90s and rolling or parallel offsets. It gives each mark's position from the end of the conduit and the matching bender mark, with a step-by-step bend mode. It stands out for offering both the bender's table and exact trigonometry, with the difference shown when it is 1/16" or more.

Resumé fra Debuts, baseret på app-siden i App Store.

Flere apps i kategorien Produktivitet

De bedste nye apps i kategorien Produktivitet denne uge

Om appen

BendSure is a conduit-bending calculator for electricians: offsets, saddles, stub-ups, back-to-back 90s, rolling offsets and parallel offsets. Enter your measurements and get the marks to make on the conduit, measured from the end of the stick, plus the mark on your bender (arrow, star or rim notch) to line up with each one.

CALCULATORS • Offsets: bend toward the obstruction or from a first bend at X, at 10, 22.5, 30, 45 or 60 degrees (angles vary by calculator) • Rolling offsets • Parallel offsets with the marks for each conduit • 3-point saddles (45/22.5 and 60/30) • 4-point saddles • Stub-up 90s • Back-to-back 90s, long and short method

NUMBERED BENDS Marks are numbered from the end of the conduit, Mark 1 first. The sketch of the bend carries the same numbers, so you can see which bend each mark belongs to, and a diagram of the stick shows where each one goes.

BEND MODE Tap Start bending to work one bend per screen: the mark in big numbers, a tape strip that shows where it falls, the bender mark to line up, and a note when to rotate the conduit 180 degrees. Tap Bent. Next after each bend. The screen stays on while you work.

EXACT MATH OR YOUR BENDER'S TABLE Every result shows the math, the multiplier and shrink used, so you can check it against your own numbers. The default is your bender's table, the numbers printed in bender guides. Exact trigonometry is one tap away. When the two differ by 1/16" or more, the result shows both answers side by side ("Your bender's table gives ..." or "Exact gives ...") with one tap to switch.

SET UP FOR YOUR BENDER On first launch, set up your bender: Klein, IDEAL, Gardner Bender, Greenlee or your own take-up, plus conduit type (EMT, rigid or IMC) and trade size (1/2" to 1-1/4"). Take-up presets are built in where a published value exists; otherwise you enter the take-up printed on your bender head. Skip it and change it any time in Settings. The setup is shown at the top of every calculator, so you always know which size an answer was for.

READABLE MARKS Results are in fractions to 1/16", the way a tape reads. Prefer metric? Switch to centimeters in Settings. On an empty calculator, Try an example fills in a worked case; New job clears the inputs, with Undo.

FIVE LANGUAGES English, German, Spanish, French and Italian. BendSure follows your phone's language, or you pick one in Settings.

PRIVATE AND OFFLINE Works offline. Anonymous usage counts only; your measurements never leave the phone. No ads, no account, no subscription.

BendSure is a calculation aid. Check every mark before you bend, and follow your local code and your bender's instructions. Not affiliated with Klein Tools, IDEAL, Gardner Bender or Greenlee.

Spørgsmål om BendSure: Conduit Bending

Hvad er BendSure: Conduit Bending?
BendSure: Conduit Bending is a productivity calculator for electricians that works out marks for offsets, saddles, stub-ups, 90s and rolling or parallel offsets. It gives each mark's position from the end of the conduit and the matching bender mark, with a step-by-step bend mode. It stands out for offering both the bender's table and exact trigonometry, with the difference shown when it is 1/16" or more.
Er BendSure: Conduit Bending gratis?
Nej. BendSure: Conduit Bending er en betalt app.
Hvilke enheder fungerer BendSure: Conduit Bending på?
BendSure: Conduit Bending fungerer på iPhone.
Hvilke sprog findes BendSure: Conduit Bending på?
BendSure: Conduit Bending findes på engelsk.
Hvem har lavet BendSure: Conduit Bending?
BendSure: Conduit Bending er lavet af Amanuel Getachew Shiferaw. Aldersgrænsen i App Store er 4+.
Hvad er alternativer til BendSure: Conduit Bending?
Lignende apps på Debuts: ChickMark: Habit Tracker, Anvil, AirBuild.

Brugernes bedømmelse

Log ind for at bedømme appen. Det vigtigste er, at du er ærlig.

Ingen bedømmelser endnu. Har du prøvet den? Giv den første bedømmelse.

Signaler for synlighed

Sådan finder AI og mennesker BendSure: Conduit Bending på Debuts
Klar til AIDelvist
78% beskrevet, så AI kan matche den
Kan findes nuLiveStrukturerede data på denne side og Debuts API

Fortæl os, hvad du kan lide. Vi sender kun en mail, når noget nyt passer, og udviklere tilføjer ofte et tilbud til testere.

Hvilken slags apps
På min
Vis kun
Hvor ofte
Vi sender et link til bekræftelse. Du får intet, før du klikker på det.