Ícone da app BendSure: Conduit Bending

BendSure: Conduit Bending

Não reivindicada

BendSure is a conduit-bending calculator for electricians: offsets, saddles, stub-ups…

Por Amanuel Getachew Shiferaw · Produtividade
Pontuação Debuts 82NovaSê o primeiro a avaliar

Porque esperamos isto: Thorough, well-explained conduit bending calculator with clear value for electricians and a helpful bend-by-bend guide.

Captura de ecrã 1 de BendSure: Conduit BendingCaptura de ecrã 2 de BendSure: Conduit BendingCaptura de ecrã 3 de BendSure: Conduit BendingCaptura de ecrã 4 de BendSure: Conduit BendingCaptura de ecrã 5 de BendSure: Conduit Bending

Apps de Produtividade semelhantes

Ver as melhores

Em resumo

BendSure: Conduit Bending is a productivity calculator for electricians that works out marks for offsets, saddles, stub-ups, 90s and rolling or parallel offsets. It gives each mark's position from the end of the conduit and the matching bender mark, with a step-by-step bend mode. It stands out for offering both the bender's table and exact trigonometry, with the difference shown when it is 1/16" or more.

Resumo do Debuts, com base na ficha da App Store.

Sobre

BendSure is a conduit-bending calculator for electricians: offsets, saddles, stub-ups, back-to-back 90s, rolling offsets and parallel offsets. Enter your measurements and get the marks to make on the conduit, measured from the end of the stick, plus the mark on your bender (arrow, star or rim notch) to line up with each one.

CALCULATORS • Offsets: bend toward the obstruction or from a first bend at X, at 10, 22.5, 30, 45 or 60 degrees (angles vary by calculator) • Rolling offsets • Parallel offsets with the marks for each conduit • 3-point saddles (45/22.5 and 60/30) • 4-point saddles • Stub-up 90s • Back-to-back 90s, long and short method

NUMBERED BENDS Marks are numbered from the end of the conduit, Mark 1 first. The sketch of the bend carries the same numbers, so you can see which bend each mark belongs to, and a diagram of the stick shows where each one goes.

BEND MODE Tap Start bending to work one bend per screen: the mark in big numbers, a tape strip that shows where it falls, the bender mark to line up, and a note when to rotate the conduit 180 degrees. Tap Bent. Next after each bend. The screen stays on while you work.

EXACT MATH OR YOUR BENDER'S TABLE Every result shows the math, the multiplier and shrink used, so you can check it against your own numbers. The default is your bender's table, the numbers printed in bender guides. Exact trigonometry is one tap away. When the two differ by 1/16" or more, the result shows both answers side by side ("Your bender's table gives ..." or "Exact gives ...") with one tap to switch.

SET UP FOR YOUR BENDER On first launch, set up your bender: Klein, IDEAL, Gardner Bender, Greenlee or your own take-up, plus conduit type (EMT, rigid or IMC) and trade size (1/2" to 1-1/4"). Take-up presets are built in where a published value exists; otherwise you enter the take-up printed on your bender head. Skip it and change it any time in Settings. The setup is shown at the top of every calculator, so you always know which size an answer was for.

READABLE MARKS Results are in fractions to 1/16", the way a tape reads. Prefer metric? Switch to centimeters in Settings. On an empty calculator, Try an example fills in a worked case; New job clears the inputs, with Undo.

FIVE LANGUAGES English, German, Spanish, French and Italian. BendSure follows your phone's language, or you pick one in Settings.

PRIVATE AND OFFLINE Works offline. Anonymous usage counts only; your measurements never leave the phone. No ads, no account, no subscription.

BendSure is a calculation aid. Check every mark before you bend, and follow your local code and your bender's instructions. Not affiliated with Klein Tools, IDEAL, Gardner Bender or Greenlee.

Perguntas sobre BendSure: Conduit Bending

O que é BendSure: Conduit Bending?
BendSure: Conduit Bending is a productivity calculator for electricians that works out marks for offsets, saddles, stub-ups, 90s and rolling or parallel offsets. It gives each mark's position from the end of the conduit and the matching bender mark, with a step-by-step bend mode. It stands out for offering both the bender's table and exact trigonometry, with the difference shown when it is 1/16" or more.
BendSure: Conduit Bending é gratuita?
Não. BendSure: Conduit Bending é uma app paga.
Em que dispositivos funciona BendSure: Conduit Bending?
BendSure: Conduit Bending funciona em iPhone.
Em que idiomas está BendSure: Conduit Bending disponível?
BendSure: Conduit Bending está disponível em inglês.
Quem criou BendSure: Conduit Bending?
BendSure: Conduit Bending é criada por Amanuel Getachew Shiferaw. A classificação etária na App Store é 4+.
Quais são as alternativas a BendSure: Conduit Bending?
Apps semelhantes no Debuts: ChickMark: Habit Tracker, Anvil, AirBuild.

A avaliação das pessoas

Inicia sessão para avaliares esta aplicação. O que conta é seres sincero.

Ainda sem avaliações. Já a experimentaste? Sê o primeiro a avaliar.

Sinais de descoberta

Como a IA e as pessoas descobrem BendSure: Conduit Bending no Debuts
Pronta para IAEm parte
78% descrita para a IA a associar
Descobrível agoraAtivaDados estruturados nesta página e a API do Debuts

Diz-nos do que gostas. Só enviamos e-mail quando surge algo novo que corresponda, e os criadores costumam acrescentar uma oferta para testadores.

Que tipo de apps
No meu
Mostrar só
Com que frequência
Enviamos um link de confirmação. Não recebes nada até clicares nele.