Appikon för BendSure: Conduit Bending

BendSure: Conduit Bending

Inget anspråk gjort

BendSure is a conduit-bending calculator for electricians: offsets, saddles, stub-ups…

Av Amanuel Getachew Shiferaw · Produktivitet
Debuts-poäng 82NyGe det första betyget

Därför förväntar vi oss mycket av den: Thorough, well-explained conduit bending calculator with clear value for electricians and a helpful bend-by-bend guide.

BendSure: Conduit Bending skärmbild 1BendSure: Conduit Bending skärmbild 2BendSure: Conduit Bending skärmbild 3BendSure: Conduit Bending skärmbild 4BendSure: Conduit Bending skärmbild 5

Liknande appar i kategorin Produktivitet

Se de bästa

Kort sagt

BendSure: Conduit Bending is a productivity calculator for electricians that works out marks for offsets, saddles, stub-ups, 90s and rolling or parallel offsets. It gives each mark's position from the end of the conduit and the matching bender mark, with a step-by-step bend mode. It stands out for offering both the bender's table and exact trigonometry, with the difference shown when it is 1/16" or more.

Sammanfattning från Debuts, baserad på appsidan i App Store.

Fler appar i kategorin Produktivitet

Veckans bästa nya appar i kategorin Produktivitet

Om appen

BendSure is a conduit-bending calculator for electricians: offsets, saddles, stub-ups, back-to-back 90s, rolling offsets and parallel offsets. Enter your measurements and get the marks to make on the conduit, measured from the end of the stick, plus the mark on your bender (arrow, star or rim notch) to line up with each one.

CALCULATORS • Offsets: bend toward the obstruction or from a first bend at X, at 10, 22.5, 30, 45 or 60 degrees (angles vary by calculator) • Rolling offsets • Parallel offsets with the marks for each conduit • 3-point saddles (45/22.5 and 60/30) • 4-point saddles • Stub-up 90s • Back-to-back 90s, long and short method

NUMBERED BENDS Marks are numbered from the end of the conduit, Mark 1 first. The sketch of the bend carries the same numbers, so you can see which bend each mark belongs to, and a diagram of the stick shows where each one goes.

BEND MODE Tap Start bending to work one bend per screen: the mark in big numbers, a tape strip that shows where it falls, the bender mark to line up, and a note when to rotate the conduit 180 degrees. Tap Bent. Next after each bend. The screen stays on while you work.

EXACT MATH OR YOUR BENDER'S TABLE Every result shows the math, the multiplier and shrink used, so you can check it against your own numbers. The default is your bender's table, the numbers printed in bender guides. Exact trigonometry is one tap away. When the two differ by 1/16" or more, the result shows both answers side by side ("Your bender's table gives ..." or "Exact gives ...") with one tap to switch.

SET UP FOR YOUR BENDER On first launch, set up your bender: Klein, IDEAL, Gardner Bender, Greenlee or your own take-up, plus conduit type (EMT, rigid or IMC) and trade size (1/2" to 1-1/4"). Take-up presets are built in where a published value exists; otherwise you enter the take-up printed on your bender head. Skip it and change it any time in Settings. The setup is shown at the top of every calculator, so you always know which size an answer was for.

READABLE MARKS Results are in fractions to 1/16", the way a tape reads. Prefer metric? Switch to centimeters in Settings. On an empty calculator, Try an example fills in a worked case; New job clears the inputs, with Undo.

FIVE LANGUAGES English, German, Spanish, French and Italian. BendSure follows your phone's language, or you pick one in Settings.

PRIVATE AND OFFLINE Works offline. Anonymous usage counts only; your measurements never leave the phone. No ads, no account, no subscription.

BendSure is a calculation aid. Check every mark before you bend, and follow your local code and your bender's instructions. Not affiliated with Klein Tools, IDEAL, Gardner Bender or Greenlee.

Frågor om BendSure: Conduit Bending

Vad är BendSure: Conduit Bending?
BendSure: Conduit Bending is a productivity calculator for electricians that works out marks for offsets, saddles, stub-ups, 90s and rolling or parallel offsets. It gives each mark's position from the end of the conduit and the matching bender mark, with a step-by-step bend mode. It stands out for offering both the bender's table and exact trigonometry, with the difference shown when it is 1/16" or more.
Är BendSure: Conduit Bending gratis?
Nej. BendSure: Conduit Bending är en betalapp.
Vilka enheter fungerar BendSure: Conduit Bending på?
BendSure: Conduit Bending fungerar på iPhone.
Vilka språk finns BendSure: Conduit Bending på?
BendSure: Conduit Bending finns på engelska.
Vem utvecklar BendSure: Conduit Bending?
BendSure: Conduit Bending är utvecklad av Amanuel Getachew Shiferaw. Åldersgränsen i App Store är 4+.
Vilka alternativ finns till BendSure: Conduit Bending?
Liknande appar på Debuts: ChickMark: Habit Tracker, Anvil, AirBuild.

Så betygsätter folk den

Logga in för att betygsätta appen. Det ärliga betyget räknas.

Inga betyg ännu. Har du provat appen? Ge det första betyget.

Signaler för upptäckt

Så upptäcker AI och människor BendSure: Conduit Bending på Debuts
AI-redoDelvis
78 % beskrivet för att AI ska kunna matcha
Går att hitta nuLiveStrukturerad data på den här sidan och Debuts API

Berätta vad du gillar. Vi mejlar bara när något nytt matchar, och utvecklare lägger ofta till ett erbjudande för testare.

Vilken sorts appar
På min
Visa bara
Hur ofta
Vi skickar en länk för att bekräfta. Inget kommer innan du har klickat på den.