Crown Cut: Miter & Bevel-sovelluksen kuvake

Get a clear setup for cutting crown molding flat on a compound miter saw

Tekijä: Maksim Berest · Apuohjelmat
Debuts-pisteet 78UusiAnna ensimmäinen arvio

Miksi odotamme sitä: Clear, well-documented miter and bevel settings for crown molding, with saw limit warnings and full offline use.

Crown Cut: Miter & Bevel, kuvakaappaus 1Crown Cut: Miter & Bevel, kuvakaappaus 2Crown Cut: Miter & Bevel, kuvakaappaus 3Crown Cut: Miter & Bevel, kuvakaappaus 4Crown Cut: Miter & Bevel, kuvakaappaus 5Crown Cut: Miter & Bevel, kuvakaappaus 6

Samankaltaiset Apuohjelmat-sovellukset

Katso parhaat

Lyhyesti

Crown Cut: Miter & Bevel is a utility app that calculates miter and bevel settings for cutting crown molding flat on a compound miter saw. Users enter the wall corner angle and pick a 38° or 45° spring angle, or enter their own measured angle, then see top and front saw views. It works offline with no account, and it can warn when a calculated angle exceeds the limits saved for a named saw profile.

Debutsin tekemä tiivistelmä App Store -listauksen pohjalta.

Lisää Apuohjelmat-sovelluksia

Viikon parhaat uudet Apuohjelmat-sovellukset

Tietoa

Get a clear setup for cutting crown molding flat on a compound miter saw.

Enter the angle between your walls and choose a 38° or 45° spring angle, or enter the measured angle of your own molding. Crown Cut calculates the miter and bevel settings and shows the directions from the operator's position.

SEE EACH STEP • Top and front saw views show how to turn the table and tilt the blade. • Choose inside or outside corners and the left or right piece. • See which molding edge goes against the fence and which side to keep. • For a left-bevel-only saw, see when to rotate the molding 180° on the table while keeping it face up.

MEASURE FROM THE RIGHT POINT • Select whether the other end is square, inside or outside. • See the existing cut, the new cut, and the wall-contact edge used for length L. • Follow long-point and short-point instructions for every end combination.

SAVE YOUR SAW AND ROOM • Add named saw profiles with separate left and right miter and bevel limits. • Receive a notice when a calculated angle exceeds your saved limits. • Use a rectangular or L-shaped room plan, record individual corner angles, mark pieces done, and share a cut list. • Use the large at-the-saw view with the screen kept awake while it is open.

Works offline. No account, advertising, subscription or in-app purchase. Room measurements and saw profiles are stored on your device. English and Russian interfaces, with automatic iPhone language selection or an in-app choice.

The calculation assumes matching molding on both walls, equal spring angles, plumb walls and a level ceiling. Room plans and saw drawings are schematic. The app checks angle limits; cutting width and height depend on your saw. Verify your setup with the saw manual and make a test joint with two scraps first.

Crown Cut is an independent app and is not affiliated with or endorsed by any saw manufacturer.

Kysymyksiä sovelluksesta Crown Cut: Miter & Bevel

Mikä Crown Cut: Miter & Bevel on?
Crown Cut: Miter & Bevel is a utility app that calculates miter and bevel settings for cutting crown molding flat on a compound miter saw. Users enter the wall corner angle and pick a 38° or 45° spring angle, or enter their own measured angle, then see top and front saw views. It works offline with no account, and it can warn when a calculated angle exceeds the limits saved for a named saw profile.
Onko Crown Cut: Miter & Bevel ilmainen?
Kyllä. Crown Cut: Miter & Bevel on ilmainen ladata.
Millä laitteilla Crown Cut: Miter & Bevel toimii?
Crown Cut: Miter & Bevel toimii laitteilla: iPhone.
Millä kielillä Crown Cut: Miter & Bevel on saatavilla?
Crown Cut: Miter & Bevel on saatavilla kielillä: englanti, venäjä.
Kuka on kehittänyt sovelluksen Crown Cut: Miter & Bevel?
Sovelluksen Crown Cut: Miter & Bevel on kehittänyt Maksim Berest. App Storen ikäraja on 4+.
Mitä vaihtoehtoja sovellukselle Crown Cut: Miter & Bevel on?
Samankaltaisia sovelluksia Debutsissa: Skysoon, Drainly: Speaker Cleaner, Photo & PDF Resize: KB.

Ihmisten arvio

Kirjaudu sisään arvioidaksesi tämän sovelluksen. Rehellisyys on tärkeintä.

Ei vielä arvioita. Oletko kokeillut sitä? Anna ensimmäinen arvio.

Löydettävyyssignaalit

Miten tekoäly ja ihmiset löytävät sovelluksen Crown Cut: Miter & Bevel Debutsissa
TekoälyvalmisOsittain
78 % kuvattu tekoälyn kohdennusta varten
Löydettävissä nytKäytössäRakenteinen data tällä sivulla ja Debuts API

Kerro, mistä pidät. Lähetämme sähköpostia vain, kun jokin uusi vastaa toiveitasi, ja kehittäjät lisäävät usein testaajille edun.

Millaisia sovelluksia
Laitteellani:
Näytä vain
Kuinka usein
Lähetämme vahvistuslinkin. Mitään ei tule, ennen kuin napsautat sitä.